Diesel generator set intake and exhaust system

Diesel generator set inlet and exhaust system diesel generator | diesel generator price / 2017-06-17
Inlet pipe
There are two kinds of intake pipes for cast iron and iron skin in the basic diesel engine. The left and right twin tubes of a V diesel engine cannot be interchanged. When installing the diesel engine, it must be noted that the joint between the intake pipe and the cylinder head must be sealed. Any debris, such as metal shavings, must not be allowed in the intake pipe. Failure to do so may result in damage to the engine. Most variants have warning signs on the air intake pipes and are required to be followed.
2. Air filter
The role of the air filter is to filter out the dust in the air, to reduce the cylinder jacket, piston group zero capture damage, the long diesel engine life. The basic type of diesel engine air filter is commonly used in two types of filter elements.
General marine non-supercharged diesel engines use inertial steel wool filter air filter air filter, land-based supercharged diesel engine multi-use paper filter composite air filter. The user shall perform regular maintenance according to the environmental conditions of use: The cleaning methods for the air cleaners of the two filter elements are now described as follows:
1. The oil bath type air filter of the inertia steel wool filter element is generally cleaned every 100 hours or so, depending on the concentration of dust in the environment. When cleaning, remove the steel wool in gasoline and dry it with compressed air. At the same time, clean the oil pool of the cleaner and add the appropriate amount of new engine oil.
2. The composite air filter of the paper filter core generally removes the dust in the dust collection basin every time it is about lOOh. Every 100-250h, remove the filter element and gently tap the end face; or use compressed air with a pressure of no more than 0.5MPa (5kgf/cm2) to blow out from the inner cavity of the filter element; you can also use a brush to gently brush the stained surface.
But do not use oil or water to clean, otherwise easily contaminated with dust, blocking the filter, resulting in insufficient intake of the diesel engine and the main output power, exhaust black smoke and other ills. If it is found that the filter element is damaged or the dirt is not easily removed, it must be replaced. The correct use and maintenance of the air filter must be taken very seriously. If the paper filter element is damaged, the sealing surface of the filter element is improperly installed and short-circuited, or the dust is too much without timely maintenance, resulting in too much dust in the oil pool. When the oil is sucked into the cylinder, the cylinder, piston and piston ring will be seriously worn. , Operational economic deterioration and other failures.
Next:Installation of diesel generator exhaust pipe and muffler
Previous:Installation, use and regulation of marine diesel generator sets

PVC double-color jelly air-blowing molding machine Operation Manual

This machine is specially applied to manufacture single color, double color slippers sandals and leisure shoes with PVC or TPR. Its features are as follows:

1. Full computer controlling, humanized man-machine interface , operating panel is concise;

2. Compared with the same kind of equipments, it saves electricity and increases efficiency;

3. Compared with the same kind of equipments, it has larger injection capacity and clamping force;

4. the rotation of station is characterized by continuously variable speed, has light noise and be steady;

5. Preparing and injection device are controlled proportionally, besides, the speed, material capacity and pressure are adjustable, which ensures the quality of products;

6. Can use it to manufacture single color, double color slippers sandals and are free to choose stations to work according to different requirements of products;

Technical Parameters

Item Unit Parameters
Raw material --- PVC
Injection Capacity(Max) cm3   565;495
Heating Power kw 10; 7
Temperature Controling point 4
Screw diameter mm φ65;φ60
Screw Speed r.p.m 0-200
Rated injection pressure Mpa 85;75
Injection Stroke(Max) mm 200
Motor power kw 18.5; 15
Clamping Force  KN 80T
Mold Size(Max)  mm 450*220*280

 

PVC Moulding Machine For Shoes

PVC Moulding Machine For Shoes,PVC Air-Blowing Molding Machine,Automatic PVC Molding Machine,PVC Moulding Machine

SHIJIAZHUANG LONGXUAN TRADING CO., LTD , https://www.longxuanmachine.com

Posted on