![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)
The concept of gear pump is very simple, that is, its most basic form is that the same size of two gears in a close-fitting rotation of the mutual engagement within the shell, the shell is similar to the internal "8" shape, two gears inside , The outer diameter of the gear and both sides of the shell with the close fit. The material from the extruder enters the middle of the two gears at the suction port and fills this space, moving along the housing as the teeth rotate, finally exiting when the two teeth mesh. In the jargon, a gear pump, also called a positive displacement device, is like a piston in a cylinder that is squeezed out mechanically as one tooth enters the fluid space of the other tooth. Because the fluid is incompressible, the liquid and the tooth can not occupy the same space at the same time, so the fluid is eliminated. As a result of the continuous meshing of the teeth, this phenomenon occurs continuously and thus provides a continuous discharge at the outlet of the pump, the same amount of discharge per revolution of the pump. As the drive shaft rotates uninterruptedly, the pump discharges the fluid without interruption. Pump flow directly with the pump speed. In fact, there is a small amount of fluid loss in the pump, which makes it impossible to achieve a pump operating efficiency of 100% because these fluids are used to lubricate both sides of the bearing and gear, and the pump body can never be gap-free Can not make the fluid 100% discharged from the outlet, so a small amount of fluid loss is inevitable. However, the pump can still run well and still achieve efficiencies of 93% to 98% for most extruded materials. For fluids with varying viscosity or density in the process, the pump will not be affected too much. If you have a damper, such as a screen or a restrictor on the side of the outlet, the pump will push fluid through them. If this damper changes at work, ie if the screen becomes dirty, clogged, or the backpressure of the restrictor is increased, the pump will still maintain a constant flow until the mechanical limit of the weakest part of the device is reached (Usually fitted with a torque limiter). There is actually a limit to the speed of a pump, depending on the process fluid, and if the oil is delivered, the pump can rotate at a high speed, but when the fluid is a high viscosity polymer melt When the body, this limit will be significantly reduced. It is very important to push the highly viscous fluid into the two-tooth space on the side of the suction port. If this space is not full, the pump can not discharge the exact flow rate, so the PV value (pressure × flow rate) is another limiting factor, and Is a process variable Due to these limitations, gear pump manufacturers will offer a range of products, namely different sizes and displacements (quantities discharged per revolution). These pumps will be matched to the specific application process to optimize system capacity and price. PEP-II pump gear and shaft together as a whole, the whole body hardening process, can get a longer working life. The "D" bearing incorporates a forced lubricating mechanism that allows the polymer to pass through the bearing surface and return to the pump inlet to ensure effective lubrication of the rotating shaft. This feature reduces the potential for polymer retention and degradation. Precision machining of the pump body allows the "D" bearings and gear shaft with precision, to ensure that the gear shaft is not eccentric, to prevent gear wear. Parkool seal structure and PTFE seal together form a water-cooled seal. This seal does not actually contact the surface of the shaft and its sealing principle is to cool the polymer to a semi-molten state to form a self-sealing. Rheoseal seals can also be used, which are machined with reverse spiral grooves on the inner surface of the shaft seal to allow the polymer to be back-pressured back into the inlet. For ease of installation, the manufacturer has designed a ring bolt mount to match the flange mounting of other equipment, which makes the manufacture of the barrel flange easier. The PEP-II gear pump comes with a heating element that matches the size of the pump and is available to the user for fast heating and thermal control. Unlike heating in the pump body, damage to these components is limited to one board, regardless of the pump. The gear pump is driven by a separate motor that effectively blocks upstream pressure pulsations and flow fluctuations. The pressure pulsation at the gear pump outlet can be controlled within 1%. In the extrusion line with a gear pump, you can increase the flow rate of output, reducing material in the extruder shear and residence time, reduce extrusion temperature and pressure pulsation to improve productivity and product quality.
fertilizer pellet machine can produce 2-8mm diameter organic and compost fertilizer pellet, biology organic or compost fertilizer from animal manure.
fertilizer pellet machine has low temperature pelletizing process . pellet shaping is high, biological bacteria survival rate is larger than 98%.
fertilizer pellet machine has full automatically lubricate spare parts oil systems, which can automatically lubricate spare parts --such as rollers, vertical shaft ,gear, bearings, very convenient to operate, but other supplier machines need to add grease after working four hours.
Organic Fertilizer Machine,Organic Fertilizer Making Machine,Organic Fertilizer Production Line,Organic Fertilizer Production Equipment
Shandong Kingoro Machinery Co., Ltd , https://www.kingoromachinery.com