Analysis of experimental discussion on smelting and shaping of spur gear

The treatment method refers to the spur gear forming process data [1-3] at home and abroad, and through experimental comparison, the extrusion forming step of the spur gear as shown is determined. On the 2000kN hydraulic universal material testing machine, four sets of spur cylindrical gear closed extrusion forming process with LD2 material were completed by using the mold device with floating mold frame. The experimental speed was 1520mmmin-1, and the appropriate amount of animal oil was applied as lubricant on the surface of the blank. The force stroke curve was recorded using a displacement sensor, a load cell, and an XY recorder.
Experimental Results The actual picture of the gear obtained from the experiment is as it is. When the gear is formed by extrusion process, the fullness of the tooth cavity, the life of the mold and the stability of the accuracy are the three most important factors affecting the quality of the closed-end extruded spur gear, especially the first two factors directly Forming loads are closely related. Therefore, it is important to analyze the relationship between load and tooth shape parameters during forming.
The influence of the modulus and the number of teeth on the upper limit force The upper limit force of the radial extrusion spur gear is related to the structural parameters such as the modulus and the number of teeth of the gear. It is found through experiments that when the other parameters are constant, the increase of the modulus will cause the unit upper limit force to decrease, and the increase of the number of teeth will increase the unit upper limit force, which is especially obvious at the end of the forming stage, and the upper limit force changes abruptly, so the tooth is also caused. The cavity is difficult to fill and the accuracy of the gear is low.
The influence of the modulus and the number of teeth on the frictional power According to the plastic forming theory, the magnitude of the friction factor is different from the change of the unit upper limit force with the reduction amount when the number of teeth is different when the number of teeth is different. Large, especially at the end of the formation, it is easy to produce upsetting. Similarly, the influence of frictional power on the formation of cold extrusion teeth is relatively large. It is known from experiments that the frictional power of cold extrusion gears always increases with the increase of modulus and number of teeth, especially at the end of deformation. Fast, when the modulus is m3, the friction power increases sharply, so when the modulus is large, the forming is greatly affected by the friction, as shown in 6.
The change of the total upper limit power during the forming process is calculated by the upper limit analysis of the extrusion of the spur gear [4, 5], and experimentally verified, in the total upper limit power of the radially extruded spur gear, when the deformation At the end of the friction power accounted for the total deformation power percentage close to the fixed value (about 10), the total shear power accounted for a small proportion, but the plastic forming power accounted for more than 90 (in the final full phase multiplied).
Analysis and Discussion The closed-type cold extrusion forming process of spur gear is a high-efficiency, time-saving and no-cutting method, but its deformation resistance is large, filling is difficult, and the life of the mold is low, which becomes a difficult problem of plastic forming. Through the above experimental data It can be seen from the analysis that the effect of extrusion is closely related to the material of the tooth blank, the parameters of the tooth profile, the friction factor, and the forming device [6, 7].
When the total upper limit power in the gear blank material extrusion molding is large, the forming effect is easily affected, and the plastic forming power accounts for 90 in the total upper limit power, and the plastic deformation power is directly affected by the metal material characteristics (strength, yield limit, etc.). Low-carbon, low-alloy steels have good plasticity and low deformation resistance, so it is effective to use low-carbon, low-alloy steel or quenched and tempered materials to form gears by precision forging.
The tooth profile parameter and the number of teeth are the most important structural parameters of the gear. The effect of the spur gear extrusion is directly related to the number of teeth and the modulus. In the case where the pitch of the gear is constant, the cold-squeezing cylindrical gear is selected to have a large modulus and a small number of teeth, which is advantageous for forming. When the number of teeth and the modulus are relatively large, it is necessary to reduce the friction factor as much as possible, and effective lubrication is necessary.
The forming device experiment found that the deformation resistance increased sharply at the end of the extrusion deformation, which seriously affected the forming effect. According to the plastic forming principle and through experiments, it can be proved that the floating mold frame can be used when designing the mold, the fixed end flow is restricted to increase the fullness of the tooth cavity or the shunt method is used to reduce the deformation resistance.
Conclusion The total upper limit power during cold forging extrusion of spur gears has a great relationship with the modulus of the gear to be formed, the number of teeth, the degree of lubrication in forming and the material properties of the blank. The frictional power of cold precision forging has a significant increase with the increase of the modulus and the number of teeth. At the end of the deformation, the deformation resistance increases sharply, especially the plastic deformation resistance increases rapidly. The friction factor is also an important factor affecting the deformation load.

All series CNI Laser modules can be fiber coupled with different core diameter MM fiber or SM fiber. You have  to refer to the detailed specs of each laser modules (such as power, stability, noise, size, etc) to decide which one is suitable for your application. We would like to do the coupling job for you.

The collimator of Fiber Coupling Laser is designed to connect to the end of FC/PC or SMA905 connector and contains an AR-coated spherical lens. The distance between the spherical lens and the tip of the FC-terminated fiber can be adjusted to compensate for focal length changes, or to re-collimate the beam at the specific wavelength and distance of interest.

Fiber Coupling Efficiency Chart (Connector: SMA905 or FC)

Laser Type Fiber Coupling Efficiency FC for SM fiber ,FC/SMA905 for MM fiber SM Fiber 4~9 µm MM Fiber ≥50 µm MM Fiber ≥100 µm MM Fiber ≥200 µm MM Fiber ≥400 µm DPSS Laser TEMoo >40% >70% >75% >80% >90% Multi transverse mode >20% >60% >70% >80% >90% Diode Laser TEMoo >30% >60% >75% >80% >90% Multi transverse mode Low >30% >65% >75% >85%

Fiber Coupling Laser

Fiber Coupling Laser,Fiber Coupled Laser,Infrared Fiber Laser System,Diode Laser Module

Changchun New Industries Optoelectronics Technology Co., Ltd. , http://www.lasersciences.com