Comprehensive Review of Causes of Unusual Wear on Forklift Tires

1 Under certain load and driving conditions, the forklift tires have a suitable tire pressure. When the tire pressure is lower than the standard value, the radial deformation of the tire increases, causing excessive deflection on both sides, resulting in grounding on both sides of the crown. The inner wall of the sidewall is under pressure, and the outer wall of the sidewall is pulled. The inner cord of the tire has large deformation and alternating stress. Periodic compression deformation will cause fatigue damage to the rewind cord, which will increase the relative slip between the tire ply and the tire and the ground. The heat generated by the friction will increase, the temperature of the tire will rise sharply, and the tensile strength of the rubber will decrease. Loose and partial delamination of the cords, punctures occur in the event of an impact. The uneven pressure on the tread makes the shoulder part wear out, resulting in a “bridge effect” and the tread is toothed or wavy. Tire pattern recesses easily embed road nails and stones, causing mechanical damage. Carcass rolling resistance increases, fuel consumption increases. Tests have shown that when the tire pressure is lower than the standard value of 20%-25%, the fuel consumption increases by 20% accordingly. When the tire pressure is higher than the standard value, the crown is grounded at the center, the contact area between the tire and the road is reduced, the load per unit area is increased, and the wear in the middle of the crown is intensified. The tire cord is overstretched, the carcass cord stress increases, the cord fatigue process is accelerated, and the cord is broken, causing the tire to burst early.

2 Under a certain load and tire pressure, the vehicle speed increases, the tire's deformation frequency, carcass vibration, and the tire's circumferential and lateral distortion (formation of standing wave) increase, and the heat generated by friction per unit time increases. The performance of the tires is reduced, and even the occurrence of cracks in the ply and the flaking of the tread may accelerate the wear and tear of the tire.

3 Under a certain tire pressure, the tire is overloaded and its deflection is increased. The stress of the cords and cords is increased, and the cords in the tire wall are easily broken, loose and delaminated. The force of the carcass cords will be affected. Exceeding the design allowable stress and the ground pressure of the tire, the amount of heat generated increases, the temperature of the carcass increases, and the carrying capacity decreases. At the same time, wear occurs due to the contact between the shoulder and the ground, especially in the case of obstacles, even a small stone can cause crown blasting. Practice has proved that in the case of driving on turning and uneven roads, when the tire load exceeds 20%, its mileage will be shortened by 35%; when it exceeds 50%, it is shortened by 59%; when it exceeds 1 time, it is shortened by more than 80%.

4 The road condition has a great influence on the service life of the tire. It affects the friction between the tire and the ground and the dynamic load on the tire.

5 The high temperature will reduce the rubber's tear strength, elongation and hardness, reduce the adhesion strength between the rubber and the cord, and accelerate the aging of the rubber. For tires that are exposed to high temperatures, especially tires that have already aged, it is easy to tear the tread pattern when they slip or roll over obstacles. Due to the aging of the sidewall rubber, cracks and severe deformation of the sidewall lead to the separation of the carcass layer cords from the rubber. Once the tyre has encountered a sudden load, it is very likely that a puncture occurs.

6 When the tire is subject to grease, acid and alkali corrosion and long-term high temperature, the physical and chemical properties of the tire will change, the carrying capacity will be greatly reduced, and it is very easy to use a tire during use. In addition, tires that have been corroded by oil will have blocky flaking of the air-encapsulant layer, rubber shedding from the small area of ​​the tread, and detachment of the carcass cord from the rubber. Because the patch cannot be affiliated with oily rubber, even if the damage to the tire is small, the possibility of repair is lost.

7Because of the different loads on the front and rear axles, different working characteristics of the driving wheels and steering wheels and differences in road conditions, the wear conditions of the tires are inconsistent. If the same axle, the same size, structure, level and pattern are not replaced on both sides of the same axle. The tires will accelerate tire wear.

8 In use, if you do not pay attention to a reasonable mix and regular exchange resulting in uneven load on the tire, it will also accelerate tire wear.

Automatic Sliding X-ray hospital Door

hospital door, hospital sliding door, medical sliding door , automatic medical airtigh door, clean room door ,operating theaters door

Hospital door

Medical sliding door , each door has a single whole steel plate , lined with aluminum profile inner frame and high strength honeycomb panels , surrounded by high quality stainless steel shut perfect treatment , high dimensional accuracy , closed surface made of high quality EPDM special rubber seal to be perfect seamless seal , Bao steel steel board used in all high-quality cold-rolled steel , the surface with high-quality weather-resistant color pure polyester electrostatic powder coating , its performance in line with GB5237.4-2000 standard (in line with European standards QUALICOA D), and the development of a variety of wood effect , Door Press (medical diagnostic X-ray emission prevention health protection requirements ) lining thickness corresponding stereotype . protective harness toward lining 2mmpb thickness , the thickness of the other 1mmbp protection , The vertical axis hinge design unique , different from the conventional hinge , changing the point of impact to avoid sagging door , making more durable protective door , you open smoothly

Automatic Medical Airtight Doors with airtight , Sound insulation , thermal insulation , fire protection , radiation protection

1 Using a small volume , high-power brushless DC motor , frequent opening and closing , also can be long-term trouble-free operation

2. The sides of the door equipped with professional vacuum airtight tape , using a unique compression technology to ensure the door when the door is closed with the close coordination to achieve reliable sealing effect

3. With foot switch and special handle , health care workers to open the door easily , when power outage it can be opened by handle

4. The Safety sensors can effectively prevent the clip people , also can be set to automatic door sensor drive from indoor

5. Also can be opened easily by a remote control

6. The user can set the sensor effects , the flexibility to set the sensor operation mode according to the doctor`s work habits and characteristics of various types of surgery , in order to achieve the best results

Designed for clean room environments such as hospital operating rooms , pharmaceutical production plants, precision equipment factories, food shop , laboratory access port

Technical parameters

Power Voltage : 220V/50HZ

Power consumption : <150w

Door weight :<200KG

Opening/Closing speed : 20-60cm/sec

Closed way: Auto/induction

Safety Light Beam Switch :

This is which accord with the European standards , with a completely interference immunity . Also accord with ESC standards and in line with the French government about the workplace regulations require automatic doors

Accord with German regulations concerning the outer doors of power starting

hospital door, hospital sliding door, medical sliding door , automatic medical airtigh door, clean room door ,operating theaters door

SHENZHEN HONGFA AUTOMATIC DOOR CO., LTD , https://www.hongfarrud.com

Posted on